#1
|
|||
|
|||
Looking for a top-end compact handlebar (and stem combo)
After much research and consultation, I've come to the conclusion that there is little point to spend $$$ on carbon handlebar and stem besides the bling factor. The arguable comfort benefit can be achieved with thicker (or gel) bar tape and better tires.
So I'm looking for a top-end compact handlebar and stem combo, preferably with a drop close to 125mm and a reach around 80mm. Any recommendation (have looked at Ritchey, Easton, and Thomson)? |
#2
|
|||
|
|||
3T Ergosum and Arx II are pretty hard to beat, IMO.
|
#3
|
|||
|
|||
The PRO stuff is awesome! I also like Easton EA90 stems but meh on the handlebars.
|
#4
|
|||
|
|||
+1
several h-bar styles and sizing to choose from with 3T and the graphics are subtle enough to fit most any paint scheme. all at good prices. Richey also hits this well too. |
#5
|
|||
|
|||
Make sure the aluminum bar and stem is the 7000 series aluminum, not the cheaper heavier 6000 series. 7000 aluminum bars and stems weigh about same as good CF ones. Example....In Ritchey products, The WCS line is 7000 series. The Pro line is not.
BTW....I'm kinda cheap about parts like this.....so on my last Cannondale build....I used Cannondale C1 stem and bar....both very light (and cheap) 7000 series aluminum. C2 and up heavier 6000 stuff. |
#6
|
||||
|
||||
I was riding the PRO Vibe 7S compact for a while and really like it but found the drop wasn't quite right for the Campy thumb shifter.
Recently went to the FSA Energy Wing Pro Compact and it's much better for the thumb position. https://www.mec.ca/en/product/5034-0...Road-Handlebar |
#7
|
|||
|
|||
Enve cross fork
Enve compact bars feel the best in my hands and the shifters sit exactly where I like them.
Stems- I have an Enve stem on one bike, but I don't have to be all matchy matchy. Carbon stems do nothing but lighten the wallet. |
#8
|
|||
|
|||
I think the PRO Vibe 7S Round is a really nice bar. It's 80 reach and 130ish drop. Haven't run Campy on that bar, but I've never had trouble reaching the thumb shifter on similar bend bars.
|
#9
|
|||
|
|||
They look good, which is important. I believe the folks at Enve say that's the real reason they make carbon stems: people who'll buy them since the look cool.
|
#10
|
|||
|
|||
Carbon stem
Oh, I have on one of my bikes. But I am not going to say that it has improved my cycling enjoyment in any measurable amount.
|
#11
|
|||
|
|||
Quote:
|
#12
|
|||
|
|||
Thanks for everyone's input so far. It seems most bar recommendations have a 130ish drop, just wonder if there is any with a 125mm drop and top quality?
|
#13
|
|||
|
|||
3T Ergonova has a 123 mm drop, i think, and a 77 mm reach.
it should just be perfect. and you could buy an alloy one (pro). or, a carbon one (team). or you could go all out and buy a top of the line carbon (ltd). |
#14
|
||||
|
||||
Zipp Service Course bars and stems are very nice. Several models to choose from, with various drop and reach combo's. A+
__________________
Cuero - Fine leather cycling gloves - GET SOME |
#15
|
|||
|
|||
Aluminum alloy designation
Careful there - the series number of aluminum alloys refers only to the primary alloying element(s), it does not directly mean that one series is stronger than another series. The strength of an aluminum alloy depends not just on its alloying elements, but also on its treatment (heat treating, aging, work hardening, etc.). There are plenty of 6000 series alloys that are stronger than 7000 series alloys. And these are not the only alloy series used in bicycles - there are plenty of components that use 2000 & 5000 series alloys, depending on requirements of the application.
|
|
|