Builder's Spotlight The Paceline Forum Builder's Spotlight


Go Back   The Paceline Forum > Image Gallery > The Showcase

Reply
 
Thread Tools Display Modes
  #1  
Old 07-31-2014, 05:07 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
Llewellyn flavour on Di2

I think it is a complicated way to enjoy cycling
however, it works well.
This punter had two carbon bikes fail with no crashes, let us be realistic, the paranoia for lower grams numbers is now well and truly into total silliness.
I recently rode a few big name carbon bikes and it was like riding a bike with solid rubber tyres, there was no give at the bars. One can do the lift and thump down test with hands pressed down on the handle bars with the same wheel swapped over to the different bikes and good grief. Some are like granite. They handle like total crap around any corners other than on billiard table like road, skating So called engineers don't know what they don't know.
If that is all you have ridden then one does not know what a nice bike feels like. Like eating Maccas, if you think that is food......................
Any how, Cadenzia lug set, Columbus tubes, Columbus steel fork, Di2 grouppo, 32 hole wheels, 28mm tyres.
Attached Images
File Type: jpg 1.jpg (145.1 KB, 934 views)
File Type: jpg 2.jpg (73.5 KB, 926 views)
File Type: jpg 3.jpg (73.1 KB, 925 views)
File Type: jpg 4.jpg (101.6 KB, 928 views)
File Type: jpg 5.jpg (94.4 KB, 928 views)
File Type: jpg 6.jpg (84.8 KB, 927 views)
File Type: jpg 7.jpg (92.2 KB, 925 views)
File Type: jpg 8.jpg (102.4 KB, 927 views)
File Type: jpg 9.jpg (101.1 KB, 918 views)
File Type: jpg 10.jpg (124.5 KB, 921 views)
File Type: jpg 11.jpg (106.5 KB, 926 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 07-31-2014 at 05:25 PM.
Reply With Quote
  #2  
Old 07-31-2014, 05:12 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
Whiizzz whhhrrrrrrr

a lathe is a beautiful thing
file file sand sand
cook
file file sand sand
yeah
that will work
Attached Images
File Type: jpg 12.jpg (117.0 KB, 924 views)
File Type: jpg 13.jpg (111.1 KB, 915 views)
File Type: jpg 14.jpg (93.6 KB, 913 views)
File Type: jpg 15.jpg (101.7 KB, 913 views)
File Type: jpg 16.jpg (81.2 KB, 910 views)
File Type: jpg 17.jpg (103.9 KB, 909 views)
File Type: jpg 18.jpg (140.5 KB, 905 views)
File Type: jpg 19.jpg (93.7 KB, 904 views)
File Type: jpg 20.jpg (109.1 KB, 894 views)
File Type: jpg 21.jpg (110.5 KB, 892 views)
File Type: jpg 22.jpg (98.9 KB, 891 views)
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #3  
Old 07-31-2014, 05:18 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
it is about metal work

not about cartons or pictures to fill out nothing
or Sun Glass adverts

bicycle metal work from my workshop for those who may find it interesting
Attached Images
File Type: jpg 23.jpg (103.4 KB, 894 views)
File Type: jpg 24.jpg (71.5 KB, 886 views)
File Type: jpg 25.jpg (95.0 KB, 885 views)
File Type: jpg 26.jpg (82.3 KB, 888 views)
File Type: jpg 27.jpg (119.5 KB, 889 views)
File Type: jpg 28.jpg (73.2 KB, 891 views)
File Type: jpg 29.jpg (96.2 KB, 886 views)
File Type: jpg 30.jpg (100.0 KB, 887 views)
File Type: jpg 31.jpg (124.8 KB, 888 views)
File Type: jpg 32.jpg (118.1 KB, 882 views)
File Type: jpg 33.jpg (91.3 KB, 886 views)
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #4  
Old 07-31-2014, 05:58 PM
rileystylee rileystylee is offline
Senior Member
 
Join Date: Jun 2012
Location: UK
Posts: 582
ART
Reply With Quote
  #5  
Old 07-31-2014, 06:33 PM
8aaron8 8aaron8 is offline
Senior Member
 
Join Date: Dec 2013
Location: Sacramento CA
Posts: 1,287
Lovely photos. I really enjoy your frame building products as well, thanks
Reply With Quote
  #6  
Old 08-01-2014, 01:23 PM
eBAUMANN's Avatar
eBAUMANN eBAUMANN is offline
Imshi Cycles
 
Join Date: Oct 2010
Posts: 8,913
bravo sir! please continue to share, as a hobby-builder myself it is always fascinating to see process photos from a true master of the craft!
__________________
For Sale --- Instagram
Reply With Quote
  #7  
Old 08-01-2014, 04:53 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
Litening to Radio National

The Australian Broadcasting Corporation , Aunty gives me brain food while I work for 11 hours on Thursday
Attached Images
File Type: jpg 1.jpg (88.9 KB, 831 views)
File Type: jpg 2.jpg (94.4 KB, 834 views)
File Type: jpg 3.jpg (129.6 KB, 835 views)
File Type: jpg 4.jpg (107.9 KB, 829 views)
File Type: jpg 5.jpg (128.4 KB, 832 views)
File Type: jpg 6.jpg (132.1 KB, 830 views)
File Type: jpg 7.jpg (119.7 KB, 831 views)
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #8  
Old 08-01-2014, 05:10 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
Took some time to nut it out

I hooked the logic circuits of a Bambleweeny 57 Sub-Meson Brain to an atomic vector plotter suspended in a strong Brownian Motion producer ( a nice hot cup of tea)

I looked at other builders with cables hooking and looping about the FD and I thought, why?
With steel you can make lots of nice details, enter stage left "the lathe"
then a few test pieces and 1.8mm is the bush thickness, shhh, don't tell any one.
Made a bush (flat surface for the grommet sit correctly against)
I chopped up one of Richards Sachs old Suntour look alike braze on mounts.
They are a nice part. File grind and braze
Bingo

Some thing like this may have been done before or similar, it would make sense if others have arrived at the same place, but I have not seen or noticed before.
Attached Images
File Type: jpg 8.jpg (88.8 KB, 824 views)
File Type: jpg 9.jpg (104.0 KB, 823 views)
File Type: jpg 10.jpg (101.1 KB, 822 views)
File Type: jpg 11.jpg (106.8 KB, 823 views)
File Type: jpg 12.jpg (93.2 KB, 817 views)
File Type: jpg 13.jpg (112.6 KB, 821 views)
File Type: jpg 14.jpg (100.8 KB, 821 views)
File Type: jpg 15.jpg (100.4 KB, 822 views)
File Type: jpg 16.jpg (94.8 KB, 817 views)
File Type: jpg 17.jpg (101.7 KB, 821 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 08-01-2014 at 05:36 PM. Reason: because
Reply With Quote
  #9  
Old 08-01-2014, 05:13 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
It is nice

that the pics are enjoyed and useful
Thank you for the kind compliments
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #10  
Old 08-01-2014, 11:29 PM
Ahneida Ride's Avatar
Ahneida Ride Ahneida Ride is offline
Senior Member
 
Join Date: Dec 2003
Location: near the factory
Posts: 174,244
Nice pictorial tutorial !!!!!!!!!!
__________________
www.HandleBra.com
Reply With Quote
  #11  
Old 08-02-2014, 01:51 PM
soulspinner soulspinner is offline
Senior Member
 
Join Date: Dec 2003
Location: rochester, ny
Posts: 8,069
Love this stuff...
__________________
chasing waddy
Reply With Quote
  #12  
Old 08-06-2014, 09:32 AM
54ny77 54ny77 is offline
Senior Member
 
Join Date: Jul 2009
Posts: 9,681
lovin' the photo series, keep 'em coming!
Reply With Quote
  #13  
Old 08-06-2014, 04:47 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
Di2 Down tube entry

I am not a fan of sharp cornered plates near the lugs
so round reinforcement plate with round corners to reduce the stress riser
Correct flat surface and 1.75mm flat surface on the inside to ensure the Shimano 6mm Grommet sits in correctly. Curved surface for the grommet to sit on is errrr, not the best.

and it is stainless so the rust will not start around the edges

The chain stay entry is the one with most heart ache.
I can see the need for designing and producing castings but Shimano will sneeze next year and change the grommet size etc
Attached Images
File Type: jpg 1.jpg (94.4 KB, 752 views)
File Type: jpg 2.jpg (88.6 KB, 748 views)
File Type: jpg 3.jpg (73.5 KB, 744 views)
File Type: jpg 4.jpg (78.2 KB, 740 views)
File Type: jpg 5.jpg (95.6 KB, 743 views)
File Type: jpg 6.jpg (96.8 KB, 740 views)
File Type: jpg 7.jpg (104.0 KB, 744 views)
File Type: jpg 8.jpg (87.8 KB, 736 views)
File Type: jpg 9.jpg (90.3 KB, 738 views)
File Type: jpg 10.jpg (98.9 KB, 736 views)

Last edited by Dazza; 08-06-2014 at 05:47 PM. Reason: because I am cranky
Reply With Quote
  #14  
Old 08-06-2014, 05:59 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
The important thing is the hole in the CS to be as small as possible
and the foot print of the reinforcement is such that a failure will never occur
Holes in tubes are never to be taken lightly
I see builders poking tubes through top tubes, chainstays and fork blades and brazing with no reinforcements, they will have failures.
The boss has to allow for the grommet to set correctly, thus 4.2mm about the tube surface and allow the newer longer Shimano Di2 wire thread through with ease.

I started with 3D CAD drawings, then a lump 28.6mm round stainless bar and started the cutting
Attached Images
File Type: jpg 1.jpg (109.8 KB, 742 views)
File Type: jpg 2.jpg (83.1 KB, 734 views)
File Type: jpg 3.jpg (92.8 KB, 733 views)
File Type: jpg 4.jpg (88.7 KB, 732 views)
File Type: jpg 5.jpg (93.4 KB, 733 views)
File Type: jpg 6.jpg (133.9 KB, 735 views)
File Type: jpg 7.jpg (100.7 KB, 734 views)
File Type: jpg 8.jpg (80.5 KB, 727 views)
File Type: jpg 9.jpg (106.1 KB, 732 views)
File Type: jpg 10.jpg (107.7 KB, 727 views)
File Type: jpg 11.jpg (93.0 KB, 729 views)
File Type: jpg 12.jpg (105.8 KB, 724 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 08-08-2014 at 03:53 PM.
Reply With Quote
  #15  
Old 08-06-2014, 06:05 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 357
Lug cutting

I attacked the Cadenzia lugs, to make them look different.
Each frame I make is a bit different than the last one.
I like lugs with curves
Attached Images
File Type: jpg a.jpg (92.9 KB, 724 views)
File Type: jpg b.jpg (96.7 KB, 720 views)
File Type: jpg c.jpg (133.2 KB, 720 views)
File Type: jpg d.jpg (109.0 KB, 719 views)
File Type: jpg e.jpg (130.3 KB, 716 views)
File Type: jpg f.jpg (120.2 KB, 711 views)
File Type: jpg g.jpg (131.8 KB, 715 views)
File Type: jpg h.jpg (131.6 KB, 716 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 08-06-2014 at 06:12 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.