|
#1
|
|||
|
|||
Possible 80's Serotta w/ aero tubing? Has anyone seen one before?
So Wednesday evening during my usual scroll through Craigslist, I came across a "Serotta Single Speed" for sale.
Of course I clicked, and I saw this frame in question. Immediately I thought that it was unique, a size I could ride, and worth checking out so I messaged the seller to come check it out and he got back to me saying we could meet Thursday evening at 7. I'll be the first to admit, I'm no Serotta pro, I haven't owned one, not for lack of want, but primarily, I am too cheap and haven't scored one.. yet. So I had to start doing some research to see just what this bike is. Problem being, I couldn't find one just like it. Which made me suspect this wasn't a Serotta after all, but maybe a repainted frame with Serotta decals. I knew it had aero tubing and started to search for bikes with AX components since the two go fairly hand in hand. But even searching for these bikes, I couldn't find anything remotely close when I was looking at the seat cluster. |
#2
|
|||
|
|||
Part 2/3
The closest thing I could find was the Shimano bike they used in the catalog which looked like it had the same unusual seat cluster:
http://theflyingwheel.blogspot.com/2...ogun-aero.html Plenty of speculation on my part, was this the Lotus Super Aero or a Tsunoda, or a Norta? I tapped out. I started a thread with our friends over at BikeForums Classic and Vintage: https://www.bikeforums.net/classic-v...l#post21768227 They were reassuring and I appreciate their responses, insofar as they were equally stumped as to where the frame could have come from. So it was up to me to wait a little until Thursday night to finally see the bike for myself. Yeah, I could have emailed the seller and asked a lot of questions, but I also didn’t want to be trouble, my style is to meet up and inspect the bike for myself and ask questions more in person to make the transaction as easy on the seller as possible. It usually pays off when it’s time to negotiate. You may also notice in that thread, I didn’t want to tip anyone off here that this bike existed, because I didn’t want someone to beat my to it. As you might know in your own craigslist dealings, things can change on a whim, and I couldn’t risk someone here jumping me in line, ☺. The bike seemed most comparable to these models: Last edited by habes78023; 10-30-2020 at 06:06 PM. |
#3
|
|||
|
|||
Part 3/3
Needless to say, I inspected the bike, and it appeared to me to be more likely to be a genuine Serotta than not, and if it wasn’t, then at least I had a cool frame that I probably wouldn’t lose everything on. The price to play was good enough for me, so into my car it went, and back home. Now it’s daylight and I got pictures to share.
I’m hoping that some of you here might have some knowledge about how this frame came about or anything else cool to say. Here’s what I do know about it: Frame: Fillet Brazed all the way around, no lugs, Aero Tubing (possibly Tange?) on the down tube and seat tube, which then oval back to wider at the bottom bracket. Fork has an engraved “S” which is the only marking I can find, besides the decals which are worse for wear. Two water bottle mounts, Two Allen head set screws for the seatpost, with a tiny phillips head screw holding a small piece of metal that is supposed to keep the seatpost from getting drilled through with the set screws. Shimano Dropouts in the front and rear but hard to read from the single speed action I checked the bottom bracket and the steerer tube for serial numbers but found none,. I do think that the paint is original, because there was purple paint up the steerer tube. Any clues on where I might find some ID? Components wise, a very interesting mix, unlikely much is original. Specialized bars and water bottle cages. 3TTT stem (that isn't a spacer, it's a cover where it hinges i believe. Aero seat post, Shimano for sure, but not 100% the model, Dia Compe levers? the hoods say that at least Dura Ace 7400 Brake calipers 105 headset and 105 crankset, unsure on bottom bracket for now. Campagnolo hubs (I'm not great at model numbers here) and I know a Mavic Module E2 rear wheel but unsure on the front, probably also a mavic but missing label i think possibly mismatched. Selle Italia Future saddle Anyway, enough talk, more pictures. Let me see if I can get these posted right. I know most are too big so I used google photos with a link below. Let me know if that doesn't work but I'm also going to try to post some on the thread for posterity. https://photos.app.goo.gl/4t54kri8AdNV4Tf9A Last edited by habes78023; 10-30-2020 at 04:54 PM. |
#4
|
||||
|
||||
I am of the belief it's actually a Serotta. The second, smaller screw on the seat post looks like a hack to make use of the wrong seat post.
I suggest reaching out to Ben Serotta. Interesting bike though. |
#5
|
|||
|
|||
Quote:
As far as the Seat Cluster, I thought the same about the smaller screw at the top, but I'm thinking now that it was part of the design to hold the small piece of metal in. Otherwise, I'm not sure that a seatpost should have that much space behind it in a frame... Now that I think more about it, it would seem that a frame builder might have a more elegant solution to the seatpost that a small screw and piece of loose metal in the seattube.. I'm not sure though, I'd like to see a Lotus or Tsunoda under the grommet with an AX seatpost to be sure. I will say, the seatpost here I do think is a Dura Ace AX aero post, and I don't think it was ground down or anything. But it definitely had a few ambitious people tighten the set screws, The rear base of the post has scarring from the lower set screw. Last edited by habes78023; 10-30-2020 at 04:58 PM. Reason: Rethinking. |
#6
|
|||
|
|||
I had a really cool Serotta funny bike for the track built for the 84 Olympics. 24 inch front wheel with aero seat and down tube. The frame was a spare or prototype and had a Serotta branded seat stay bridge and only had a white primer finish. Finished it with a rattle can and rode it for a couple of years, a great handling bike. Sold it to the dad of a promising Jr rider for probably way less than it would be worth today. While hanging around a framebuilders shop a few weeks ago, I saw a number of steel aero tubes on bikes and inbuilt. I was tempted but had my mind set on something else.
|
#7
|
||||
|
||||
The dimensions for the Columbus aero post from the era are 30mm x 16mm. You may want to check it against your seat tube.
|
#8
|
||||
|
||||
I can't say for sure either way - that said I'm skeptical because in all my time there I never saw anything like this associated with the brand.
It could be a one-off that was made before my time...if it was built by Ben or the boys it would have a serial number for sure. dave |
#9
|
|||
|
|||
I dunno what it is but I 100% would have bought it too.
|
#10
|
|||
|
|||
@steelbikerider That's awesome! I did see those funny bikes in the search for a bike comparable to this one. I even saw one that had handlebars brazed to the top of the fork, that was wild too.
@velomateo A campy post would fit for sure, looks like it's longer than the one that is in there now, but not by a lot.. You'll have to forgive me for my non metric measurements. But the seatpost there now measures 1.125" and just over .6875", whereas the campy measurements you give are 1.181" and .630". That being said, there is plenty of space all around either way you look at the seat tube, so either Shimano or Campagnolo would fit right now, |
#11
|
|||
|
|||
I've had two clubs with that exact purple, forkcrown looks correct, interesting I've never seen one before
|
#12
|
|||
|
|||
@Toeclips Exactly my thoughts, the paint looks too good to be a simple respray and decal job... and I joked on the other thread, I'm sure I have a genuine Serotta fork if nothing else, haha.
@mtechnica Agree, I think most of us would have probably paid the price of admission for this one. It's just too interesting and cool to pass up. @David Kirk Thanks for your input, I was hoping you would stumble across the post from your previous replies in my time spent researching. I was thinking it might have been before you would know for sure. But I will say I was disappointed to not find an easy serial number. I am going to get the fork another look tomorrow morning and I'll clean it up and inspect closer. I didn't even clean off some of the old grease and grime because I wanted to wait until I had good light to take pictures. You never know what clues you might wipe away during cleaning... |
#13
|
||||
|
||||
Quote:
|
#14
|
|||
|
|||
Quote:
A Campy post 30mmx16mm would be a loose fit, very similar to how the current post fits. That said, possibly there's a different post out there that would actually fit, no little metal wedge needed. I'll do some searching to see if anyone made one larger. I appreciate the tip, the AX seatposts came with a grommet to go around the post and frame, which lead me to think that maybe there was already gaps around the post by design. I'd like to see one of the Lotus/Tsunoda Aero frames with the post installed but the grommet off to see what those gaps are (if any) |
#15
|
|||
|
|||
Looking at what the Shimano catalog says for AX, I think this probably does have the wrong post installed, I'd say probably an E Type, SP-7322 at 29mm x 18.5mm, whereas it actually requires a SP-7320 C Type, which has more of a teardrop shape.. measurements supposed to be 34.1mm x 18mm.
As if the aero seatposts weren't rare enough, they made them in different sizes so the search is going to be even more difficult. @velomateo Thanks for the suggestion, it makes sense that they would have gone and modified considering how hard it is to just find one of these aero posts, and all they want to do is ride, so grab the first post that fits somewhat and make it go. Last edited by habes78023; 10-31-2020 at 10:13 AM. |
|
|