#16
|
|||
|
|||
I've been maybe unnecessarily scared to dry tpu or latex since I run alu rims and rim brakes on all my bikes
|
#17
|
|||
|
|||
#18
|
|||
|
|||
Quote:
It is very rare I get a flat, can't even remember the last time. I use the Vittoria latex tubes. I do have to pump them up every ride but use an air compressor so no big deal. TPU are lighter and I am tempted to try them but have no reason as long as my latex tubes keep going. |
#19
|
|||
|
|||
I've tried them both. The TPU work and ride just fine. I do use Vittoria latex tubes in several bikes. I do have to pump them up daily. I think the ride is slightly better than the TPU, only slightly.
__________________
A bad day on the bike is better than a good day at work! |
#20
|
|||
|
|||
I went from butyl to latex to TPU and back to latex. the main reason was the fragility of the TPU as compared to the other tubes. I tried both turbolito and pirelli tubes and had issues with both flatting or being easily damaged during install. I also found TPUs to be much more susceptible to pinch flats if pressure was not perfect.
I am back to either silca latex or vittoria latex tubes. I ride with alloy rims and rim brakes and have no issues. |
#21
|
|||
|
|||
When switching to TPU tubes, have any of you found it necessary to run higher PSI than you would with butyl or latex?
|
#22
|
||||
|
||||
I've had good success using TPU as a spare tube in my saddle bag. Very light, takes up no space, but haven't actually put on in yet, as my tubeless system hasn't failed me yet.
|
#23
|
||||
|
||||
Quote:
I'm still here.
__________________
©2004 The Elefantino Corp. All rights reserved. |
#24
|
||||
|
||||
When I tried TPU, Cyclami versions, I clipped a small rock in the road and suffered an instant blowout. I was going down a steep hill and I still can't believe I stayed up. Put in the spare TPU and that also flatted after a mile or so, also losing air instantly, due to a wee hole in the sidewall caused by the rock.
For now, I am back on butyl and keep 2 spare TPUs in the saddle bag. Not sure if my experience is normal but punctures on butyl have never been instant....there was always a softening of the tire to let me know. I have read elsewhere that TPU loose air rapidly and was wondering what experiences others have had. Also, the high incidence of new tubes having valve issues gives me pause. Tim |
#25
|
|||
|
|||
FWIW, there seem to be many light and lighter ga. Even super light for disc brake only.
I stick with ones like the Aerothons, the weight speaks for itself. Nike here gave me some lighter ones, carry the 40gram ones as spares, the super/stupid light ones I fear in the wild.
__________________
This foot tastes terrible! |
#26
|
||||
|
||||
i recently did some research on this just thinking about waste and found these articles interesting
yellocrank tpu pt 1 / pt 2 tldr - butyl is dirty to produce and ends up in landfill if you don't seek out recycle programs latex while natural and (possibly) biodegrades generally is harvested in SE Asia with little regulation so you get deforestation and slave labor. no infrastructure to recycle TPU requires least resources to manufacture and some are 100% recyclable (for whatever that is worth) i've ridden all 3 and my 2 cents regarding use butyl - irritates my skin, hate to handle it, cheapest and easiest to get ahold of, least nice ride quality. latex - rides the nicest to me, i don't mind pumping my tires pre ride as i like to play with psi regularly anyway and like to know where i'm at. i did return a few challenge latex tubes as i found big bubbles in them (when pumped very low psi) when i was checking them before install tpu - like others have said, ride almost as nice as latex and the most packable making for great spares even if you get on better with latex or butyl. i did find you have to be delicate when using a mini pump. because of the violent pumping/shaking i damaged one at the base of the core when replacing a tube mid ride, i think it was a ridenow. i've flatted all three and can't say if one is more resilient than the other, too many variables pandapodium ends up cheap with free shipping these aren't as cheap as the ridenow but they have removeable cores and they make a TPU sealant. haven't tried this setup yet but it seems like it could be the way to go. also i haven't tried this yet but i went about looking for a tpu patch solution and found this stuff from gear aid (also on amazon) which looks promising. should be cheaper than anything else and you can cut to whatever size and shape you like
__________________
IG Last edited by br0qn; 02-06-2024 at 03:16 PM. |
#27
|
||||
|
||||
Deep(ish) dive by Cycling Weekly.
__________________
©2004 The Elefantino Corp. All rights reserved. |
#28
|
|||
|
|||
Quote:
|
#29
|
||||
|
||||
I'm predominantly a tubeless guy, but my Dura Ace 9000 wheels, although supposedly tubeless, are hardly posterboys for the technology. So I installed Schwalbe Aerothan tubes instead. At first I wasn't impressed, but when I lowered the pressure to 65-70psi (I'm 140lbs, running 26mm Panaracer GK Slicks on the aforementioned wheels) they started to feel amazing. Over 1000 miles and no flats yet, but I hardly ever puncture anyway so that's indicative of nothing. They feel great, though, and what's more the tubes are so small and light that you can put 'em in a jersey pocket and they take up very little real estate and you don't feel 'em there either.
Many moons ago I used Vittoria latex tubes. Never again. They just lose air too quickly. Like 20psi+ over the course of a single day. |
#30
|
|||
|
|||
Quote:
|
|
|