Builder's Spotlight The Paceline Forum Builder's Spotlight


Go Back   The Paceline Forum > Image Gallery > The Showcase

Reply
 
Thread Tools Display Modes
  #1  
Old 07-31-2014, 04:07 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
Llewellyn flavour on Di2

I think it is a complicated way to enjoy cycling
however, it works well.
This punter had two carbon bikes fail with no crashes, let us be realistic, the paranoia for lower grams numbers is now well and truly into total silliness.
I recently rode a few big name carbon bikes and it was like riding a bike with solid rubber tyres, there was no give at the bars. One can do the lift and thump down test with hands pressed down on the handle bars with the same wheel swapped over to the different bikes and good grief. Some are like granite. They handle like total crap around any corners other than on billiard table like road, skating So called engineers don't know what they don't know.
If that is all you have ridden then one does not know what a nice bike feels like. Like eating Maccas, if you think that is food......................
Any how, Cadenzia lug set, Columbus tubes, Columbus steel fork, Di2 grouppo, 32 hole wheels, 28mm tyres.
Attached Images
File Type: jpg 1.jpg (145.1 KB, 905 views)
File Type: jpg 2.jpg (73.5 KB, 898 views)
File Type: jpg 3.jpg (73.1 KB, 896 views)
File Type: jpg 4.jpg (101.6 KB, 900 views)
File Type: jpg 5.jpg (94.4 KB, 899 views)
File Type: jpg 6.jpg (84.8 KB, 898 views)
File Type: jpg 7.jpg (92.2 KB, 896 views)
File Type: jpg 8.jpg (102.4 KB, 898 views)
File Type: jpg 9.jpg (101.1 KB, 890 views)
File Type: jpg 10.jpg (124.5 KB, 893 views)
File Type: jpg 11.jpg (106.5 KB, 897 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 07-31-2014 at 04:25 PM.
Reply With Quote
  #2  
Old 07-31-2014, 04:12 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
Whiizzz whhhrrrrrrr

a lathe is a beautiful thing
file file sand sand
cook
file file sand sand
yeah
that will work
Attached Images
File Type: jpg 12.jpg (117.0 KB, 895 views)
File Type: jpg 13.jpg (111.1 KB, 887 views)
File Type: jpg 14.jpg (93.6 KB, 885 views)
File Type: jpg 15.jpg (101.7 KB, 884 views)
File Type: jpg 16.jpg (81.2 KB, 881 views)
File Type: jpg 17.jpg (103.9 KB, 881 views)
File Type: jpg 18.jpg (140.5 KB, 876 views)
File Type: jpg 19.jpg (93.7 KB, 876 views)
File Type: jpg 20.jpg (109.1 KB, 866 views)
File Type: jpg 21.jpg (110.5 KB, 864 views)
File Type: jpg 22.jpg (98.9 KB, 863 views)
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #3  
Old 07-31-2014, 04:18 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
it is about metal work

not about cartons or pictures to fill out nothing
or Sun Glass adverts

bicycle metal work from my workshop for those who may find it interesting
Attached Images
File Type: jpg 23.jpg (103.4 KB, 866 views)
File Type: jpg 24.jpg (71.5 KB, 857 views)
File Type: jpg 25.jpg (95.0 KB, 857 views)
File Type: jpg 26.jpg (82.3 KB, 860 views)
File Type: jpg 27.jpg (119.5 KB, 860 views)
File Type: jpg 28.jpg (73.2 KB, 862 views)
File Type: jpg 29.jpg (96.2 KB, 858 views)
File Type: jpg 30.jpg (100.0 KB, 859 views)
File Type: jpg 31.jpg (124.8 KB, 860 views)
File Type: jpg 32.jpg (118.1 KB, 855 views)
File Type: jpg 33.jpg (91.3 KB, 858 views)
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #4  
Old 07-31-2014, 04:58 PM
rileystylee rileystylee is offline
Senior Member
 
Join Date: Jun 2012
Location: UK
Posts: 564
ART
Reply With Quote
  #5  
Old 07-31-2014, 05:33 PM
8aaron8 8aaron8 is offline
Senior Member
 
Join Date: Dec 2013
Location: Sacramento CA
Posts: 1,136
Lovely photos. I really enjoy your frame building products as well, thanks
Reply With Quote
  #6  
Old 08-01-2014, 12:23 PM
eBAUMANN's Avatar
eBAUMANN eBAUMANN is online now
Ride Metal
 
Join Date: Oct 2010
Location: QUINCY, MA (02169)
Posts: 7,788
bravo sir! please continue to share, as a hobby-builder myself it is always fascinating to see process photos from a true master of the craft!
__________________
Imshi Cycles --- Instagram
Reply With Quote
  #7  
Old 08-01-2014, 03:53 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
Litening to Radio National

The Australian Broadcasting Corporation , Aunty gives me brain food while I work for 11 hours on Thursday
Attached Images
File Type: jpg 1.jpg (88.9 KB, 803 views)
File Type: jpg 2.jpg (94.4 KB, 806 views)
File Type: jpg 3.jpg (129.6 KB, 806 views)
File Type: jpg 4.jpg (107.9 KB, 800 views)
File Type: jpg 5.jpg (128.4 KB, 804 views)
File Type: jpg 6.jpg (132.1 KB, 803 views)
File Type: jpg 7.jpg (119.7 KB, 804 views)
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #8  
Old 08-01-2014, 04:10 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
Took some time to nut it out

I hooked the logic circuits of a Bambleweeny 57 Sub-Meson Brain to an atomic vector plotter suspended in a strong Brownian Motion producer ( a nice hot cup of tea)

I looked at other builders with cables hooking and looping about the FD and I thought, why?
With steel you can make lots of nice details, enter stage left "the lathe"
then a few test pieces and 1.8mm is the bush thickness, shhh, don't tell any one.
Made a bush (flat surface for the grommet sit correctly against)
I chopped up one of Richards Sachs old Suntour look alike braze on mounts.
They are a nice part. File grind and braze
Bingo

Some thing like this may have been done before or similar, it would make sense if others have arrived at the same place, but I have not seen or noticed before.
Attached Images
File Type: jpg 8.jpg (88.8 KB, 797 views)
File Type: jpg 9.jpg (104.0 KB, 796 views)
File Type: jpg 10.jpg (101.1 KB, 795 views)
File Type: jpg 11.jpg (106.8 KB, 796 views)
File Type: jpg 12.jpg (93.2 KB, 790 views)
File Type: jpg 13.jpg (112.6 KB, 794 views)
File Type: jpg 14.jpg (100.8 KB, 794 views)
File Type: jpg 15.jpg (100.4 KB, 795 views)
File Type: jpg 16.jpg (94.8 KB, 790 views)
File Type: jpg 17.jpg (101.7 KB, 794 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 08-01-2014 at 04:36 PM. Reason: because
Reply With Quote
  #9  
Old 08-01-2014, 04:13 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
It is nice

that the pics are enjoyed and useful
Thank you for the kind compliments
__________________
Cheers Dazza

www.llewellynbikes.com
Reply With Quote
  #10  
Old 08-01-2014, 10:29 PM
Ahneida Ride's Avatar
Ahneida Ride Ahneida Ride is offline
Administrator
 
Join Date: Dec 2003
Location: near the factory
Posts: 174,244
Nice pictorial tutorial !!!!!!!!!!
__________________
www.HandleBra.com
Reply With Quote
  #11  
Old 08-02-2014, 12:51 PM
soulspinner soulspinner is offline
Senior Member
 
Join Date: Dec 2003
Location: rochester, ny
Posts: 7,722
Love this stuff...
__________________
chasing waddy
Reply With Quote
  #12  
Old 08-06-2014, 08:32 AM
54ny77 54ny77 is offline
Senior Member
 
Join Date: Jul 2009
Posts: 8,706
lovin' the photo series, keep 'em coming!
Reply With Quote
  #13  
Old 08-06-2014, 03:47 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
Di2 Down tube entry

I am not a fan of sharp cornered plates near the lugs
so round reinforcement plate with round corners to reduce the stress riser
Correct flat surface and 1.75mm flat surface on the inside to ensure the Shimano 6mm Grommet sits in correctly. Curved surface for the grommet to sit on is errrr, not the best.

and it is stainless so the rust will not start around the edges

The chain stay entry is the one with most heart ache.
I can see the need for designing and producing castings but Shimano will sneeze next year and change the grommet size etc
Attached Images
File Type: jpg 1.jpg (94.4 KB, 726 views)
File Type: jpg 2.jpg (88.6 KB, 722 views)
File Type: jpg 3.jpg (73.5 KB, 718 views)
File Type: jpg 4.jpg (78.2 KB, 714 views)
File Type: jpg 5.jpg (95.6 KB, 717 views)
File Type: jpg 6.jpg (96.8 KB, 714 views)
File Type: jpg 7.jpg (104.0 KB, 718 views)
File Type: jpg 8.jpg (87.8 KB, 711 views)
File Type: jpg 9.jpg (90.3 KB, 713 views)
File Type: jpg 10.jpg (98.9 KB, 711 views)

Last edited by Dazza; 08-06-2014 at 04:47 PM. Reason: because I am cranky
Reply With Quote
  #14  
Old 08-06-2014, 04:59 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
The important thing is the hole in the CS to be as small as possible
and the foot print of the reinforcement is such that a failure will never occur
Holes in tubes are never to be taken lightly
I see builders poking tubes through top tubes, chainstays and fork blades and brazing with no reinforcements, they will have failures.
The boss has to allow for the grommet to set correctly, thus 4.2mm about the tube surface and allow the newer longer Shimano Di2 wire thread through with ease.

I started with 3D CAD drawings, then a lump 28.6mm round stainless bar and started the cutting
Attached Images
File Type: jpg 1.jpg (109.8 KB, 717 views)
File Type: jpg 2.jpg (83.1 KB, 709 views)
File Type: jpg 3.jpg (92.8 KB, 708 views)
File Type: jpg 4.jpg (88.7 KB, 707 views)
File Type: jpg 5.jpg (93.4 KB, 708 views)
File Type: jpg 6.jpg (133.9 KB, 710 views)
File Type: jpg 7.jpg (100.7 KB, 709 views)
File Type: jpg 8.jpg (80.5 KB, 702 views)
File Type: jpg 9.jpg (106.1 KB, 707 views)
File Type: jpg 10.jpg (107.7 KB, 702 views)
File Type: jpg 11.jpg (93.0 KB, 704 views)
File Type: jpg 12.jpg (105.8 KB, 699 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 08-08-2014 at 02:53 PM.
Reply With Quote
  #15  
Old 08-06-2014, 05:05 PM
Dazza Dazza is offline
Vendor
 
Join Date: Nov 2008
Location: Down under, Brisbane
Posts: 320
Lug cutting

I attacked the Cadenzia lugs, to make them look different.
Each frame I make is a bit different than the last one.
I like lugs with curves
Attached Images
File Type: jpg a.jpg (92.9 KB, 699 views)
File Type: jpg b.jpg (96.7 KB, 695 views)
File Type: jpg c.jpg (133.2 KB, 695 views)
File Type: jpg d.jpg (109.0 KB, 694 views)
File Type: jpg e.jpg (130.3 KB, 691 views)
File Type: jpg f.jpg (120.2 KB, 686 views)
File Type: jpg g.jpg (131.8 KB, 690 views)
File Type: jpg h.jpg (131.6 KB, 691 views)
__________________
Cheers Dazza

www.llewellynbikes.com

Last edited by Dazza; 08-06-2014 at 05:12 PM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.