Removing stuck pedal?

[tuscanyswe]

So bought a crank with some pedals still in em. Bolts were somewhat rounded allrdy but now after beeing succesfull on non driveside the driveside is now completely rounded.

These are time xpresso in a chorus carbon crank. Im out of ideas with no bolt to even work on. These were bathing in rust loosener for 2 days before i went for it. Perhaps premature after beeing lucky with non driveside.. :/

Any suggestions?

[mktng]

Axle is messed anyways. Anyway to remove the pedal body off the axle and just take vice grips to it ?

Sent from my SM-N900W8 using Tapatalk

[cmbicycles]

Did you try using gentle heat? Carbon cranks, so no blowtorches, but a hair dryer may warm it up some to get some expansion for penetrating oil to seep in further.

I guess it takes an 8mm hex wrench, so no use going to sae as 5/16 is the same size. If it uses a 6mm, you can try going up to 1/4".

A straight flute pipe extractor might give enough purchase to turn it loose, a spiral extractor should turn it the right direction but might need to drill to give enough surface area to grab.

You can try to take off the pedal body and put it in a vise. You will sacrifice the pedal, most likely at this point as the bolt is rounded off, but should save the crankarm.

Don't get frustrated if one attempt doesn't work, it will come loose and patience is your friend.

[MattTuck]

yeah, put it in a vice to hold the pedal steady and turn the crank.

[tuscanyswe]

No i haven't tried gentle heat yet, thought that would do little good but would be worth a try if i can't get it loose in the wise.
I haven't taken apart a time xpresso before but i guess thats a good idea to start with. Hopefully the axle is sturdy enough to put in a wise.

Yeah dont really care about the pedals regardless. Im one of those who still rides spd on road bikes..

Thanks guys

[oldpotatoe]

Originally Posted by tuscanyswe

I haven't taken apart a time xpresso before but i guess thats a good idea to start with. Hopefully the axle is sturdy enough to put in a wise.

Yeah dont really care about the pedals regardless. Im one of those who still rides spd on road bikes..

Thanks guys

Pretty sure a c clip holds axle into body. If you can get that out, body comes off. Axle in vice, turn crank. Hopefully metal insert in crank doesn't break loose instead of axle. RH side, lefty loosely.

[Veloo]

Is it the same as this pedal?

https://www.youtube.com/watch?v=ANFk4OQB_w4

[tuscanyswe]

Yes identical actually. Looks easy enough. Haven't gotten around to this yet.
Thx peter n veloo

[jc031699]

Sometimes a torx bit will purchase where an Allen will not.

[Macadamia]

yeah if you don't care about the pedals I'd try vice grips on the spindle for purchase. Other options include filing/dremeling wrench flats onto spindle.

I've had a lot of luck using my foot to push down on stuck pedals on old bikes while holding the wrench. But those cranks were always in bikes so maybe put the crank into a bike if you don't have a suitable vise?

[mktng]

Originally Posted by Macadamia

yeah if you don't care about the pedals I'd try vice grips on the spindle for purchase. Other options include filing/dremeling wrench flats onto spindle.

I've had a lot of luck using my foot to push down on stuck pedals on old bikes while holding the wrench. But those cranks were always in bikes so maybe put the crank into a bike if you don't have a suitable vise?

Not to mention the crankset construction. Less brute force, the better !

[CaptStash]

IS my memory correct, aren't you in Seattle? If so, I have all the tools. Hit me with a PM if you want and we can arrange for you to swing by. I can promise that we'll either break it loose (or break the crank arm!).

Captstash....

[tuscanyswe]

If you are referring to me? that would have been great but I'm a long way from seattle, as in stockholm sweden .)

I do however have a bikeshop workbench with all the tools at my disposal so ill get it out sooner or later argh .)

Thanks v much for offering!

[CaptStash]

Originally Posted by tuscanyswe

If you are referring to me? that would have been great but I'm a long way from seattle, as in stockholm sweden .)

I do however have a bikeshop workbench with all the tools at my disposal so ill get it out sooner or later argh .)

Thanks v much for offering!

Yeah that's a little too far, I'd spin by but the airline would probably take a dim view of me carrying my hammer aboard! For jobs like this, cycling tools aren't necessarily what you need. I would suggest using a hammer or mallet of some sort though. The shock of a hammer blow as opposed to constant pressure can be very helpful in breaking something loose. I spent a lifetime taking things apart and putting them back together on ships; so I've seen more than my fair share of things that were frozen-up and came apart using elbow grease. I'm confident you'll get the pedal out without killing the cranks.

CaptStash....

[nickrenfro]

Yeah.. like someone else said if you don't care then try heat. Also wouldn't hurt to throw some liquid wrench on there and try using a vice or wrench to pry that sucker off.